TEST 1: Testing The 5 Volt Reference Signal

How To Test The 3.0L Ford Throttle Position Sensor (TPS)

The first thing that we're going to do is make sure that the throttle position sensor is getting power. This power is in the form of 5 Volts DC.

The wire that supplies these 5 Volts to the TPS, is the wire labeled with the number 3 in the photo above.

If 5 Volts are present, then our next step is to check that the TPS is getting Ground in TEST 2.

Let's get testing:

  1. 1

    If the engine isn't already at normal operating temperature, start it and let it warm up.

  2. 2

    Once it's warmed up, turn it off and remove any thing that may be blocking access to the throttle position sensor on the intake manifold's throttle body.

  3. 3

    Disconnect the TPS from its electrical connector.

  4. 4

    Set the multimeter function to Volts DC mode

    Don't have a digital multimeter? Need to buy one? Click here to see my recommendations: Buying A Digital Multimeter For Automotive Diagnostic Testing.

  5. 5

    Probe the wire identified with the number 3 in the photo, with the red multimeter test lead and an appropriate tool (like a wire-piercing probe or a back probe).

  6. 6

    Connect the black multimeter test lead to a good and clean Ground point on the engine or directly on the negative (-) battery terminal.

  7. 7

    Rotate the key to its ON position but don't start the engine.

  8. 8

    The multimeter should display 4.5 to 5 Volts on its screen.

Let's take a look at what your test results mean:

CASE 1: The multimeter registered 4.5 to 5 Volts. This is the correct test result and confirms that the fuel injection computer and the circuit is supplying the TPS with power.

The next step is to test the Signal Return Circuit. For this test go to: TEST 2: Testing The Sensor Return (Ground) Circuit.

CASE 2: The multimeter DID NOT register 4.5 to 5 Volts. Then the computer or the circuit are NOT providing the voltage that the TPS needs to operate.

The two most likely reasons for this are: 1) an open-circuit problem in the circuit or 2) the PCM may be fried.

Altho' it's beyond the scope of this article to test these two conditions, you have now eliminated the throttle position sensor (TPS) on your Mustang as being the cause of the problem and/or the TPS diagnostic trouble code (DTC) lighting up the check engine light (CEL).

TEST 2: Testing The Sensor Return (Ground) Circuit

How To Test The 3.0L Ford Throttle Position Sensor (TPS)

So the TPS is getting power, according to the result of TEST 1. The second step is to verify that it also has a good Ground.

NOTE: As mentioned in the previous page, the PCM is the one that provides this Ground internally, so be careful and don't accidentally or intentionally apply power (12 Volts) to this circuit or you'll fry the PCM.

OK, here are the test steps:

  1. 1

    Place your multimeter in Volts DC mode.

  2. 2

    Disconnect the TPS from its electrical connector.

  3. 3

    Probe the circuit labeled with the number 1 in the photo, with the black multimeter test lead.

  4. 4

    Connect the red multimeter test lead to the battery positive (+) terminal.

  5. 5

    Turn the key to its ON position but don't start the engine.

  6. 6

    The multimeter should display 10 to 12 Volts if Ground is present.

CASE 1: The multimeter showed 10 to 12 Volts. This is the correct test result and tells you that the PCM and the wire/circuit (that supply this Ground) are OK.

The next step is to verify that the TP sensor is creating a good throttle position signal the PCM can use. For this test go to: TEST 3: Testing The TP Signal.

CASE 2: The multimeter DID NOT show 10 to 12 Volts. This test result usually indicates a problem with either the PCM (internal fault/problem) or an open in the wire between the TPS and the PCM itself.

Altho' testing these two conditions are beyond the scope of this article, you have now eliminated the throttle position sensor (TPS) on your Ford vehicle as being the cause of the problem and/or the TPS diagnostic trouble code (DTC) lighting up the check engine light (CEL).

Ford Vehicles:

  • Aerostar 3.0L
    • 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997
  • Taurus 3.0L
    • 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007

Ford Vehicles:

  • Probe 3.0L
    • 1990, 1991, 1992
  • Ranger 3.0L
    • 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008
  • Tempo 3.0L
    • 1992, 1993, 1994

Ford Vehicles:

  • Windstar 3.0L
    • 1995, 1996, 1997, 1998, 1999, 2000

Mercury Vehicles:

  • Sable 3.0L
    • 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005

Mercury Vehicles:

  • Topaz 3.0L
    • 1992, 1993, 1994

Mazda Vehicles:

  • B3000 3.0L
    • 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007