P0107 -What Does It Mean? (1995-1999 3.8L V6 Buick, Chevrolet, Pontiac, Olds)

A trouble code P0107: MAP Sensor Circuit Low Voltage is probably one of the most common MAP sensor trouble codes that'll pop up and illuminate the check engine light.

In this tutorial, I'll explain what this trouble code means. I'll also talk about some of the tests you can perform to find its cause and solution.

You can find this tutorial in Spanish here: Código P0107 ¿Qué Significa? (1996-1999 3.8L V6 Buick, Chevrolet, Pontiac, Olds) (at: autotecnico-online.com).

APPLIES TO: This tutorial, on the P0107 OBD II trouble code, applies to the following vehicles:

• 3.8L Buick LeSabre: 1996, 1997, 1998, 1999.
• 3.8L Buick Park Avenue: 1996, 1997, 1998, 1999.
• 3.8L Buick Regal: 1996, 1997, 1998, 1999.
• 3.8L Buick Riviera: 1996, 1997, 1998, 1999.

• 3.8L Chevrolet Lumina: 1998, 1999.
• 3.8L Chevrolet Monte Carlo: 1998, 1999.

• 3.8L Oldsmobile 88 (Eighty-Eight): 1996, 1997, 1998, 1999
• 3.8L Oldsmobile 98 (Ninety-Eight): 1996
• 3.8L Oldsmobile Intrigue: 1998, 1999
• 3.8L Oldsmobile LSS: 1996, 1997, 1998, 1999
• 3.8L Oldsmobile Regency: 1997, 1998

• 3.8L Pontiac Bonneville: 1996, 1997, 1998, 1999
• 3.8L Pontiac Grand Prix: 1997, 1998, 1999

What Does Trouble Code P0107 Mean?

A P0107: MAP Sensor Circuit Low Voltage sets when the following conditions are met:

• No throttle position sensor (TPS) codes are present.
• The throttle position sensor is reporting a throttle plate angle greater than 0% (usually 0.5 Volts DC) with an engine speed less than 1000 RPM (engine at idle).
• Or, the throttle position sensor is reporting a throttle plate angle greater than 6% (usually 0.8 Volts DC) with an engine speed greater than 1000 RPM (which means you're stepping on the accelerator pedal).
• The MAP sensor's signal voltage is stuck at a value of less than 0.1 Volt while the engine is running.

To better understand why this is a problem, take a look at the section: What Does The MAP Sensor Do?

Common Symptoms Of A P0107 Trouble Code

The manifold absolute pressure (MAP) sensor is tasked with measuring the vacuum pressure in the intake manifold.

This vacuum pressure measurement is then used by the fuel injection computer to calculate engine load.

Since it's an important component of the engine management system, when it fails, engine performance will suffer. You'll see one or more of the following symptoms:

• Check engine light illuminated.
• Rough or low idle.
• Very high idle.
• Engine may start and stall.
• Little to no acceleration.
• Black smoke comes out of the tailpipe when the engine is running.

What Does The MAP Sensor Do?

The MAP sensor's job is to inform the fuel injection computer the intake manifold's vacuum pressure when the engine is running.

When the engine is idling and the throttle plate is closed, intake manifold pressure is high.

This high intake manifold pressure will cause the MAP sensor to produce a low voltage signal (usually around 2 Volts DC).

As you step on the accelerator pedal, the throttle plate opens and the engine accelerates. This causes a decrease in intake manifold vacuum pressure.

This low intake manifold pressure will cause the MAP sensor to produce a high voltage signal. At wide open throttle (like when you trying to run that red light), the MAP sensor produces a voltage around 4 Volts DC.

As long as the fuel injection computer sees the MAP sensor voltage signal decreasing/increasing, as you step on or off the accelerator pedal, it knows that the MAP sensor is functioning correctly.

What Causes A P0107 Trouble Code?

The most common cause of a P0107 trouble code is generally a bad MAP sensor.

Other things that can cause a P0107 trouble code are:

• The MAP sensor is not getting 5 Volts due to an open-circuit or short-circuit problem in its 5 Volt supply wire.
• An open-circuit problem in the MAP sensor signal wire between the MAP sensor and the fuel injection computer.
• An short-circuit to Ground problem in the MAP sensor signal wire between the MAP sensor and the fuel injection computer.
• A bad MAP sensor connector.
• Bad fuel injection computer (although very rare).

How To Diagnose And Repair A P0107 Trouble Code

Troubleshooting and resolving a P0107 involves testing the MAP sensor.

The test involves confirming that the MAP sensor is stuck at or below 0.1 Volts as you apply/release vacuum to the sensor.

Then making sure that the MAP sensor is getting 5 Volts and Ground from the fuel injection computer.

You can conclude that the MAP sensor is bad, and needs to be replaced, if your test results confirm:

• That the MAP sensor signal voltage DOES NOT decrease/increase as you apply/release vacuum to the sensor.
• That the MAP sensor is getting 5 Volts.
• That the MAP sensor is getting Ground.

You can find the MAP sensor test explained in detail here: How To Test The MAP Sensor (1995-1999 3.8L V6 Buick, Chevrolet, Pontiac, Olds).

Where To Buy The MAP Sensor And Save

There are a lot of knock-off parts that you can buy on the cheap, but that'll only last a few weeks. The following links will help you comparison shop for original equipment (OE) MAP sensor:

More 3.8L V6 GM Tutorials

You can find a complete list of 3.8L GM V6 tutorials in this index:

• GM 3.8L Index Of Articles.

Here's a small sample of the tutorials you'll find in the index:

• How To Test The MAF Sensor (GM 3.8L V6 1996-2005).
• How To Test A Does Not Crank Condition -Case Study (GM 3.8L).
• GM 3.8L Ignition Control Module And Crank (3X, 18X) Sensor Test.
• How To Test The Ignition Coil Pack -Misfire Troubleshooting Tests (GM 3.8L).