How To Test The Starter Motor (1997-2001 2.0L Honda CR-V)

By: Abraham Torres-Arredondo
Created: 02 January 2018
Updated: 15 November 2024
Articl Id: 695

Page 2 of 2

TEST 2: Verifying The Start Signal

Verifying The Start Signal. How To Test The Starter Motor (1997, 1998, 1999, 2000 And 2001 2.0L Honda CR-V)

In this test section, we're going to check that the start signal is being received by the starter motor on your Honda CR-V.

This signal is sent to the starter motor when you turn the key to crank and start your Honda CR-V's engine.

We're gonna' use a multimeter to check for this voltage signal.

OK, let's get started:

1
Disconnect the wire that connects to the S terminal of the starter motor solenoid.
2
Connect the red multimeter test lead to the female terminal of the wire you just disconnected from the S terminal of the starter motor.
3
Attach the black multimeter test lead to a clean and rust-free spot on the engine or on the vehicle frame.

I recommend that you use a battery jump start cable to Ground the black multimeter test lead directly to the battery negative (-) terminal.
4
Have your helper crank the engine from inside your Honda CR-V.

The engine won't turn over, but the idea is to verify that the starter motor's internal solenoid is getting the 12 Volt start signal from the ignition switch (or not).
5
Your multimeter is going to register one of two results: Either 9 - 12 Volts DC or no voltage at all.

Let's examine your test result:

CASE 1: The multimeter registered 10 to 12 Volts. This is the correct and expected test result and lets you know that the start signal is being received by the starter motor.

You can also conclude that the ignition switch and safety neutral switch are working the way they should.

The next test is to check the battery cable that connects to the starter motor. Go to: TEST 3: Voltage Drop Testing The Battery (+) Cable.

CASE 2: Your multimeter DID NOT register 10 to 12 Volts. This test result lets you know that the starter motor is not cranking the engine because the start signal is missing.

The most common cause of this missing start signal is usually a bad neutral safety switch or a bad ignition switch. Although it's beyond the scope of this tutorial to test these two, you have eliminated the starter motor as a cause of the problem.

TEST 3: Voltage Drop Testing The Battery (+) Cable

Voltage Drop Testing The Battery (+) Cable. How To Test The Starter Motor (1997, 1998, 1999, 2000 And 2001 2.0L Honda CR-V)

In this last test we're gonna' test the cable that connects the starter motor to the battery.

This cable is the one that provides the current that the starter motor needs to turn the engine over.

In some cases, hidden corrosion will keep the full amount of available current from reaching the starter motor.

By doing a simple multimeter voltage drop test, we can find out if this is happening or not.

IMPORTANT: Don't disconnect the battery cable from the starter motor's solenoid. In the illustration the battery cable is disconnected from the starter motor just to make it easier to show the multimeter test connections.

These are the test steps:

1
Place your multimeter in Volts DC mode.
2
Attach the red multimeter test lead to the center of the positive (+) battery terminal.

If the positive battery post isn't clean, clean a spot right on the top of it. It's important that the multimeter lead make contact right in the center of the positive battery post.
3
With the black multimeter test lead, touch the center of the starter S terminal stud to which the big battery cable attaches to. You'll maintain the black multimeter test lead in this position throughout the next step.
4
Have your helper crank the engine even though the starter motor isn't cranking the engine.

This is important, since a voltage drop test has to be done while the component in question is working (or trying to work).
5
If all is good (no voltage drop), your multimeter will register 0 Volts (.5 Volts is still 0 Volts).

If there's a voltage drop (which is bad), your multimeter will register voltage (usually above 7 Volts DC.)

Let's take a look at what your results mean:

CASE 1: Your multimeter registered 0 Volts (no voltage drop). This result indicates that the starter motor is receiving all of the battery voltage and amperage it needs to crank the vehicle.

You can conclude your Honda CR-V's starter motor is defective if you have:

Confirmed that the starter motor doesn't work when you apply power to the S terminal wire of the starter motor (TEST 1).
Confirmed that the starter motor is receiving the crank signal (TEST 2).
In this test step, you have confirmed that no voltage drop exists on the battery positive cable.

Replacing the starter motor should solve your no-crank condition.

I'm going to make two more recommendations to you:

Before removing the starter motor, manually turn the engine using a 1/2 ratchet and the appropriate socket. This is to make sure that the engine or the A/C compressor have not locked up and causing the no-crank condition.
Bench test the starter motor after removing it. This is a super easy test to do and this tutorial will help: Bench Testing The Starter Motor.

CASE 2: Your multimeter registered 5 Volts or more. This result tells you that a voltage drop does exist and that the battery's full power is not reaching the starter motor.

The good news is that this can easily be corrected, since a voltage drop is always caused by some sort of corrosion issue on the battery positive cable or terminals or the battery positive post.

The solution is to thoroughly clean the battery positive post and the battery positive (+) terminal (both the end that attaches to the battery positive post and the end the connects to the starter motor's battery (+) cable stud.

After cleaning, try cranking the engine. If it cranks and starts, no further testing is required.