How To Test The Rear O2 Sensor Heater (1996 4.0L Jeep Cherokee)

TEST 2: Making Sure The Heater Is Getting Ground

Making Sure The Heater Is Getting Ground. How To Test The Downstream Oxygen Sensor's Heater (1996 4.0L Jeep Cherokee)

The black with white stripe (BLK/WHT) wire of the O2 sensor's engine wiring harness connector is the wire that supplies the O2 sensor's heater with Ground at all times (it's a chassis Ground).

We'll do a simple multimeter voltage test to confirm the presence of Ground in the BLK/WHT wire.

If the BLK/WHT wire is providing Ground to the heater, then we'll move on to the last test (TEST 3) and check the heater element's internal resistance.

OK, let's get testing:

  1. 1

    Disconnect the O2 sensor from its engine wiring harness connector.

    NOTE: The O2 sensor's engine wiring harness connector has male terminals.

  2. 2

    Set your multimeter to Volts DC mode.

  3. 3

    Connect the red multimeter test lead to the battery positive (+) terminal.

  4. 4

    With the black multimeter test lead, gently probe the male terminal that connects to the BLK/WHT wire.

    NOTE: This is the male terminal of the engine wiring harness connector.

  5. 5

    Your multimeter should read 10 to 12 Volts DC if the BLK/WHT wire is providing Ground.

Let's take a look at your test results:

CASE 1: The BLK/WHT wire is providing Ground. This is the correct test result and it confirms that Ground is being supplied to the rear O2 sensor's heater element.

With this test result we can move on to the last test: TEST 3: Testing The Heater Element's Resistance.

CASE 2: The BLK/WHT wire IS NOT providing Ground. Without Ground the O2 sensor's heater will not function.

The most likely cause of this missing Ground is an open-circuit problem in the BLK/WHT wire. Between the O2 sensor connector and the engine.

Your next step is to repair the Ground wire and repeat the test.

TEST 3: Testing The Heater Element's Resistance

Testing The Heater Element's Resistance. How To Test The Downstream Oxygen Sensor's Heater (1996 4.0L Jeep Cherokee)

With this last test we're gonna' find out if the heater element, within the rear O2 sensor, is fried or not.

We'll accomplish this by checking that the heater element's resistance is within specification (4 to 6 Ohms).

If the downstream O2 sensor's heater element is not within specification, then you can correctly conclude that its bad and needs to be replaced. You'll also confirm that the P0147 trouble code was telling the truth.

OK, this is what you need to do:

  1. 1

    Locate the O2 sensor's female terminals labeled with the numbers 1 and 2 (in the illustration above).

    These female terminals are on the O2 sensor connector itself (not the engine wiring harness O2 connector).

  2. 2

    Place your multimeter in Ohms mode.

  3. 3

    Measure the resistance across terminals 1 and 2 of the O2 sensor itself with the multimeter test leads.

  4. 4

    Your multimeter should register 4 to 6 Ωs.

    If the heater element is fried, your multimeter will show an open (usually indicated by the letters OL) or a number over 10 K Ωs.

Let's take a look at your test results:

CASE 1: The O2 sensor's heater resistance is within specification. This is the correct and expected test result.

Since the O2 sensor's heater element is within specification, you can now conclude that the O2 sensor itself is not the cause of the oxygen sensor trouble code lighting up your check engine light.

CASE 2: Your multimeter showed an open circuit (OL). This confirms that the O2 sensor's heater element is fried.

To be a bit more specific: you can conclude the downstream O2 sensor's heater element is defective if you have:

  • Confirmed that the downstream O2 sensor's heater element is getting 12 Volts (TEST 1).
  • Confirmed that the downstream O2 sensor's heater element is getting Ground (TEST 2).
  • In this test, you have confirmed that the heater element's resistance IS NOT within specification.

Replacing the rear oxygen sensor will solve the P0147 trouble code lighting up the check engine light on your Jeep Cherokee.

More 4.0L Jeep Cherokee Tutorials

You can find a complete list of diagnostic tutorials and wiring diagrams for the 4.0L Jeep Cherokee here:

Here's a sample of the tutorials you'll find in the index:

Thank You For Your Donation

If this info saved the day, buy me a beer!

If This Info Saved the Day, Buy Me a Beer!