1994 Ford 3.0L Ranger PCM Pin Out Chart

1994 3.0L Ford Ranger PCM 60 Pin Connector

The 1994 3.0L V6 Ford Ranger is equipped with the E.E.C IV system and so its computer has 60 pins.

Whether you're tracing down an electrical short or testing one of the input/output components of the PCM, pinout charts come in handy. Below you'll find the description of each pin.

1994 3.0L Ford Ranger 60 Pin Connector
Pin Wire Color Description
 1 YEL Keep Alive Power (KAPWR)
 2 LT GRN Brake On-Off (BOO) Switch
 3 GRY/BLK Vehicle Speed Sensor (VSS) (+)
 4 WHT/PNK Ignition Diagnostic Monitor (IDM)
 5 -- Not Used
 6 PNK/ORG Vehicle Speed Sensor (VSS) (-)
 7 LT GRN/RED Engine Coolant Temp (ECT) Sensor
 8 TAN/LT BLU Fuel Pump Monitor (FPM)
 9 PNK/LT BLU MAF Ground
10 DK GRN/ORG A/C Compressor
11 GRN/YEL Canister Purge (CANP) Solenoid
12 LT BLU/ORG or LT GRN/ORG Injector 6
13 -- Not Used
14 -- Not Used
15 TAN/BLK Injector 5
16 ORG/RED Ignition Module Ground
17 PNK/LT GRN Check Engine Light (CEL)
18 TAN/ORG Data (+)
19 PNK/LT BLU Data (-)
20 BLK/LT GRN Case Ground
21 WHT/LT BLU Idle Air Control (IAC) Valve
22 LT BLU/ORG Fuel Pump Relay Control
23 -- Not Used
24 -- Not Used
25 GRY Intake Air Temp (IAT) Sensor
26 BRN/WHT VREF (5 Volt Reference - EGR Position Sensor, TPS, MAP Sensor)
27 BRN/LT GRN DPFE
28 -- Not Used
29 -- Not Used
30 LT BLU/YEL Clutch Switch (MT only)
Park Neutral Safety Switch (AT only).
31 -- Not Used
32 -- Not Used
33 BRN/PNK EGR Control (EVR) Solenoid
34 --- Not Used
35 BRN/LT BLU Injector 4
36 PNK SPOUT
37 RED Ignition Battery Power
38 -- Not Used
39 BRN/YEL Injector 3
40 BLK/WHT PWR Ground
41 -- Not Used
42 -- Not Used
43 RED/BLK O2 Sensor (Left)
44 GRY/LT BLU O2 Sensor (Right)
45 -- Not Used
46 GRY/RED Signal Return (Sensor Ground)
47 GRY/WHT Throttle Position Sensor (TPS) Signal
48 WHT/PPL Self Test Input (STI)
49 -- Not Used
50 LT BLU/RED MAF Signal
51 -- Not Used
52 -- Not Used
53 PPL/YEL Torque Convertor Clutch Solenoid
54 PNK/YEL Air Conditioning
55 -- Not Used
56 GRY/ORG Profile Ignition Pickup (PIP)
57 RED VPWR (From PCM Power Relay)
58 TAN Injector 1
59 WHT Injector 2
60 BLK/WHT Power Ground
1994 3.0L Ford Ranger PCM 60 Pin Connector

Safety Precautions

Here are some very important safety precautions when testing the wires coming out of the 60 pin PCM connector.

  1. If one or any of the wires on your Ford pickup DO NOT match the color stated in the pin out charts, then you should not use the pin out charts in this article. Why? Because this is the clearest indication that these ARE NOT the connector pin out charts for your particular Ford 3.0L Ranger.
  2. Never probe the front of the connector.
    • You should use a wire piercing probe and probe the wire a few inches away from the connector.
    • You should use a back-probe.
  3. You should never disconnect any of the PCM connectors without first disconnecting the battery negative (-) terminal.

Disclaimer

I've made every effort to double and triple check the above info (and in the next couple of pages) and I've used the best sources to compile it, but nothing in life is perfect. I don't have a staff of proof readers or editors, I'm just a little guy typing this stuff up in my spare time to help and give back to the Do-It-Yourself community. So without further ado, here's my disclaimer:

© copyright Abraham Torres-Arredondo: This information is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

If you do spot errors, please let me know. You can use the contact form at the end of the article.

Thank You For Your Donation

If this info saved the day, buy me a beer!

If This Info Saved the Day, Buy Me a Beer!