How To Test The Fuel Pump (1991-1994 3.0L V6 Ford Ranger)

How To Test The Fuel Pump (1991, 1992, 1993, 1994 3.0L Ford Ranger And Mazda B3000)

The fuel pump pressure test is not difficult to perform on the 1991-1994 Ford Ranger with a 3.0L V6 engine.

In this tutorial, I'll explain the fuel pressure test procedure. With your test result, you'll quickly determine if the fuel pump is good or bad.

In Spanish You can find this tutorial in Spanish here: Cómo Probar La Bomba De Combustible (1991-1994 3.0L V6 Ford Ranger) (at:

APPLIES TO: This tutorial applies to the following vehicles:

  • 3.0L Ford Ranger: 1991, 1992, 1993, 1994.
  • 3.0L Mazda B3000: 1994.

NOTE: The following tutorials will help you test the fuel pump on the 1995-2001 3.0L Ford Ranger:

Symptoms Of A Bad Fuel Pump

The job of the fuel pump is to deliver fuel to the engine so it can start and run.

As the fuel pump wears out and fails, it will cause one of two problems.

  • An engine no-start problem.
  • An engine performance problem.

A fuel pump failure doesn't always result in an engine no-start problem. In some cases, the fuel pump runs but does not produce enough pressure to keep the engine running at peak performance.

A faulty fuel pump that isn't producing enough fuel pressure will cause one or more of the problems listed below:

  • Engine takes longer than usual to start (extended cranking).
  • Engine idle is very rough.
  • Engine backfires thru' the intake manifold under load.
  • Engine starts, then dies.
  • Lack of power when accelerating the engine under load.
  • The check engine light illuminated by lean air/fuel mixture diagnostic trouble codes.

Whether the fuel pump is causing an engine no-start problem or an engine performance problem, a fuel pressure test will help you determine if it is the source of the problem.

Where To Buy A Fuel Pressure Test Gauge

To check the fuel pump, the fuel pressure tester requires an adapter for the Ford Schrader valve. Without it, you cannot connect the tester to check fuel pressure.

The fuel pressure gauges in the list below are quality tools and all come with the Ford Schrader valve adapter.

Fuel Pump Pressure Specification

Year/Engine/Model KOEO KOER
1995-1997 3.0L Ranger 35-45 PSI 30-45 PSI
Year/Engine/Model KOEO KOER
1995-1997 3.0L B2300 35-45 PSI 30-45 PSI

KOEO = Key On Engine Off.

KOER = Key On Engine Running.

Using A Fuel Pump Pressure Tester To Test The Fuel Pump

To accurately test if your fuel pump is good or bad, you need to use a fuel pressure gauge.

If the fuel pump is functioning properly, its fuel pressure value will be within the specified fuel pressure specification.

If the fuel pump is defective, the fuel pressure recorded by the fuel pressure gauge will not be within specification.

IMPORTANT: If the engine does not start, check the fuel pump inertia switch and reset it if necessary. A fuel pump inertia switch activated by a vehicle impact (or even just hitting the curb) will cut power to the fuel pump and cause an engine no-start problem. You can find out more about it and its location here: Fuel Pump Inertia Switch Commonly Asked Questions (1991-2008 3.0L Ford Ranger).

NOTE: The Schrader valve is located on the fuel injector rail, next to the fuel pressure regulator and on the passenger side of the engine.

These are the test steps:

  1. 1

    Remove the plastic dust cap from the Schrader valve.

  2. 2

    Place a shop towel around the Schrader valve.

    The shop towel's job is to absorb any fuel that may leak when doing step 2.

  3. 3

    Connect the fuel pressure test gauge to the Schrader valve.

  4. 4

    When ready, ask your helper to cycle the key ON and OFF but don't crank the engine while you observe the fuel pressure tester's gauge.

    Check your connections for fuel leaks. Resolve any fuel leaks before continuing to the next step.

  5. 5

    Crank the engine and check the fuel pressure gauge.

  6. 6

    Your fuel pressure gauge should register the specified fuel pressure.

Let's interpret your test result:

CASE 1: The fuel pressure gauge read 0 PSI. This confirms that the fuel pump is not supplying the fuel the engine needs to start.

This usually means that the fuel pump is bad and needs to be replaced.

CASE 2: The fuel pressure gauge registered the specified fuel pressure specification. This test result lets you know that the fuel pump is working properly.

You can conclude that the fuel pump is fine and is not responsible for the engine no-start problem.

CASE 3: The fuel pressure gauge has registered a fuel pressure well below specification. This test result indicates that the fuel pump is defective.

Ford Vehicles:

  • Ranger 3.0L V6
    • 1991, 1992, 1993, 1994

Mazda Vehicles:

  • B3000 3.0L V6
    • 1994