PCM Connector Pin Out Chart (1999 5.4L V8 Ford F150, F250 Light Duty)

1999 5.4L V8 Ford F150 And F250 PCM 104 Pin Connector

The EEC-V powertrain control module (PCM) has a 104 pin connector. To aid you in correctly identifying the connector pins, the back side of the connector (wire side) is embossed with a few numbers.

APPLIES TO: The PCM connector pinout applies on to the following vehicles:

  • 5.4L Ford F150: 1999
  • 5.4L Ford F250 Light Duty: 1999

WIRE COLOR LEGEND: You can find the wire color legend here: PCM Connector Pinout Wire Color Legend.

PCM 104 Pin Connector
Pin Wire Color Description
 1 LT GRN/YEL Ignition Coil 6
 2 ---
 3 BLK/WHT Power Ground
 4 ---
 5 ---
 6 ORG/YEL E40D SS1
 7 PNK Transfer Case Speed Sensor
 8 ---
 9 ---
10 ---
11 VIO/ORG E4OD SS2
12 WHT/LT GRN Over Drive (OD) OFF Indicator
13 VIO Data Link Connector
14 LT BLU/BLK 4x4 LOW Ind Switch (4x4 only)
15 PNK/LT BLU Data Link (-)
16 TAN/ORG Data Link (+)
17 --
18 ---
19 ---
20 BRN/ORG E4OD Coast Clutch Solenoid (CCS)
21 DK BLU Crankshaft Position (CKP) Sensor (+)
22 GRY Crankshaft Position (CKP) Sensor (-)
23 ---
24 ---
25 BLK Case Ground
26 LT GRN/WHT Ignition Coil 1
27 LT GRN/YEL Ignition Coil 5
28 ---
29 TAN/WHT Trans Control Switch (TCS)
30 ---
31 ---
32 DK GRN/VIO Knock Sensor
33 ---
34 YEL/BLK Digital Trans Range (DTR) Sensor -TR1
35 RED/LT GRN Bank 1 Sensor 2 O2 Signal
36 TAN/LT BLU MAF Sensor Signal Return (Ground)
37 ORG/BLK Trans Fluid Temp (TFT)
38 ---
39 GRY Intake Air Temp (IAT) Sensor
40 DK GRN/YEL Fuel Pump Monitor (FPM)
41 BLK/YEL A/C Clutch Signal
42 ---
43 ---
44 ---
45 ---
46 BRN Intake Manifold Communicator (IMCC) Control
47 BRN/PNK EGR Vacuum Regulator (EVR) Solenoid Control
48 ---
49 LT BLU/BLK Digital Trans Range (DTR) Sensor -TR2
50 WHT/BLK Digital Trans Range (DTR) Sensor -TR4
51 BLK/WHT Power Ground
52 WHT/BLK Ignition Coil 3

WIRE COLOR LEGEND: You can find the wire color legend here: PCM Connector Pinout Wire Color Legend.

NOTE: You can find the 1998 and 1999 4.6L Ford F150 and F250 pickup PCM pinouts here:

E-Series Vans: You can find the 1999 5.4L Ford E150, E250, and E350 van PCM connector pinout here:

1999 5.4L V8 Ford F150 And F250 PCM 104 Pin Connector

Safety Precautions

Here are some very important safety precautions when testing the wires coming out of the 104 pin PCM connector.

  1. If one or any of the wires on your Ford pickup DO NOT match the color stated in the pin out charts, then you should not use the pin out charts in this article. Why? Because this is the clearest indication that these ARE NOT the connector pin out charts for your particular Ford pickup.
  2. Never probe the front of the connector.
    1. You should use a wire piercing probe and probe the wire a few inches away from the connector.
    2. You should use a back-probe.
  3. You should never disconnect any of the PCM connectors without first disconnecting the battery negative (-) terminal.

Disclaimer

I've made every effort to double and triple check the above info (and in the next couple of pages) and I've used the best sources to compile it but nothing in life is perfect. I don't have a staff of proof readers or editors, I'm just a little guy typing this stuff up in my spare time to help and give back to the Do-It-Yourself community. So without further ado, here's my disclaimer:

© copyright Abraham Torres-Arredondo: This information is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

If you do spot errors, please let me know. You can use the contact form at the end of the article.