How To Test Engine Compression (3.0L Nissan)

How To Do An Engine Compression Test (3.0L Nissan D21 Pickup, Quest, Maxima, Pathfinder)

In this tutorial, you'll find instructions on how to do and interpret a compression test on your 3.0L equipped Nissan Maxima (Pathfinder, Quest or D21 Pickup).

You'll also find the 'Wet' compression test explained so that if you do find a cylinder with low (or no) compression, you can find out if it's due to worn cylinder head valves or bad compression piston rings.

In Spanish You can find this tutorial in Spanish here: Cómo Verificar La Compresión Del Motor (3.0L Nissan) (at:

Important Tips And Suggestions

TIP 1: If your 3.0L equipped Nissan starts and runs, it's standard procedure to do the compression test with a slightly warmed up engine. The key words here are 'slightly warmed up engine' since the engine should not be hot.

To slightly warm up the engine, start her up (from a completely cold condition) and let her run for no more than 10 to 12 minutes.

TIP 2: You'll be working around a cranking engine as you perform the engine compression test so take all necessary safety precautions. Your safety is your responsibility, so use common sense and think safety all of the time.

TIP 3: Never remove the spark plugs with a hot engine. This is important because the 3.0L V6 engine has aluminum cylinder heads. Removing the spark plugs from a hot engine can damage the spark plug hole threads in the aluminum cylinder heads.

Symptoms Of Engine Compression Problems

For the most part, engine compression problems cause one of two major types of problems:

  • The engine cranks but doesn't start: This usually happens when all four cylinders don't produce enough compression to ignite the air/fuel mixture within them.
  • The engine starts, but runs with a misfire or with a rough idle: This usually happens when one cylinder's compression is lower than the others.

When the engine starts and runs, but has a compression problem, you'll notice one or more of the following symptoms:

  • Power Loss: Your car might feel sluggish or like it's just not as peppy as it used to be, especially when accelerating.
  • Poor Fuel Economy: This bad gas mileage is caused by the engine running with an underperforming cylinder or cylinders (that aren't contributing equally to its overall power output).
  • Misfiring Engine: The engine will misfire when you come to a stop and the engine runs at idle RPMs. As soon as you step on the accelerator pedal, the misfire disappears. On OBD II equipped vehicles, you may also see one or more of the following diagnostic trouble codes illuminating the check engine light:
    • P0300: Random Cylinder Misfire.
    • P0301: Cylinder #1 Misfire.
    • P0302: Cylinder #2 Misfire.
    • P0303: Cylinder #3 Misfire.
    • P0304: Cylinder #4 Misfire.
    • P0305: Cylinder #5 Misfire.
    • P0306: Cylinder #6 Misfire.
  • Blue Exhaust Smoke: You may see blue smoke coming out of the tailpipe (as the engine runs or when you accelerate it).
  • Strange Noises: You may hear knocking or tapping sounds coming from the engine.

Which Compression Tester Should I Buy?

There are lot of engine compression testers to choose from and many places to buy them. I'm gonna' make two recommendations to you:

1) Which one to buy:  The engine compression tester that I have always used is the Actron CP7827 Compression Tester Kit. My only complaint about this engine compression tester is that it does not come with a case to store it in.

2) Where to buy:  You can buy an engine compression tester in any auto parts store in any neighborhood, in any city, but you'll be paying at least twice as much. Go to the above compression tester links, browse and compare, you'll see a big price difference!

TEST 1: Dry Compression Test

How To Do An Engine Compression Test (3.0L Nissan D21 Pickup, Quest, Maxima, Pathfinder)

To test the engine's compression, you'll need to remove all six spark plugs. My recommendation is to label all spark plug wires (or ignition coils) and spark plugs with the cylinder number to which they belong to. This is done for two reasons:

  1. To install everything back faster and without complications.
  2. To diagnose a cylinder's misfire back to a specific component (like a worn out spark plug, damaged spark plug wire, etc.).

Also, it's a good idea to blow compression air around the spark plug before removing it to remove any large particles that may fall into the spark plug hole (after you've removed the spark plug).

OK, to get started this is what you'll need to do:

  1. 1

    Disable the ignition system (if distributor equipped) by disconnecting the ignition distributor and/or the ignition coil from their electrical connectors. NOTE: Do not skip this step since disabling the ignition system will prevent ignition system damage.

  2. 2

    Disable the fuel system by removing the fuel pump fuse. Disabling the fuel system will prevent fuel from being injected into each cylinder when the test is performed.

  3. 3

    Remove the spark plugs from a slightly warmed up engine (if it starts and runs). Remember, the engine can not be hot.

    When removing the spark plugs, be careful not to drop any of them on the floor, or you run the risk of having the spark plugs porcelain insulator crack and then you'll have a misfire on your hands.

    If the engine does not start, don't worry about it being warmed up.

  4. 4

    Thread the engine compression gauge into the spark plug hole for the number 1 engine cylinder. Hand tighten the compression gauge only! Do not use any type of tool to get it tight.

  5. 5

    Have your helper crank the engine till the needle on the compression gauge stops climbing.

    Now, record on paper the value at which the needle stopped and the number of the engine cylinder on a piece of paper. Release the pressure on the gauge and repeat this step one more time.

    Repeat this test step on the remaining 3 cylinders.

Let's take a look at what your test results mean:

CASE 1: Your vehicle does NOT start and you got 0 PSI on all cylinders. This test result usually means that the engine has a serious internal mechanical problem.

The engine might have one of the following:

  • Timing belt/chain problem.
  • Blown head gasket problem.
  • Engine threw a rod.

Any compression value below 100 PSI (even if it is not 0 PSI) means internal mechanical engine trouble.

CASE 2: The compression values differ from one another. This could be normal or it could be causing a problem.

To find out if the low compression values are withing a normal range or not, go to: Interpreting The Results Of The Engine Compression Test.

CASE 3: All 6 cylinders have a compression value of less than 100 PSI. This indicates an internal engine problem.

This test result is usually caused by one of the following:

  • Timing belt/chain problem.
  • Worn piston rings.
  • Worn cylinder head valves.

Nissan Vehicles:

  • D21 Pickup 3.0L
    • 1990, 1991, 1992, 1993, 1994
  • Quest 3.0L
    • 1993, 1994, 1995, 1996, 1997, 1998
  • Maxima 3.0L
    • 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999
  • Pathfinder 3.0L
    • 1993, 1994, 1995, 1996

Infiniti Vehicles:

  • I30 3.0L
    • 1997, 1998, 1999

Mercury Vehicles:

  • Villager 3.0L
    • 1993, 1994, 1995, 1996, 1997, 1998